Home » Plumbing Services » Tips For Faucet Repair

Recent Comments

No comments to show.

Tips For Faucet Repair

Here are some tips from Plumbers in Northwest Arkansas for basic faucet repair. Replace a cartridge, ceramic disc valve, or O-ring. Use a small flathead screwdriver to remove decorative faucet caps. If the faucet has an O-ring, you can pull it straight up. If the faucet has a cartridge, use a pipe wrench or tongue-and-groove pliers to remove the cartridge retaining nut. Replace the cartridge if necessary.

Fixing A Dripping Faucet


To fix a dripping faucet, you need to understand what’s going wrong with the leaking faucet. For starters, you should know what kind of faucet it is. If it’s a compression faucet, you will need pliers to remove the handle. You can also use a hex-key wrench to loosen the nut. Once you have the nut off, you can start to work on the faucet.

To fix a dripping faucet, first determine what type of faucet you have. If you have a traditional faucet, you should use white vinegar to clean it. In addition, the dripping faucet can signal other problems with the fittings or pipes. If this is the case, you should call a plumber. If you can’t locate an expert, you can always try a DIY repair by removing the faucet handle.

Another common cause of a dripping faucet is mineral buildup. This deposits inside the valves and causes water to leak. In addition to valves, the supply tubes may also need replacement. Once these are replaced, the dripping faucet is fixed. But if this still doesn’t fix the problem, you might have to buy a new faucet. It’s not difficult to fix a dripping faucet.

Replacing A Cartridge

To replace a faucet cartridge, turn off the water supply and locate the retaining clip. In most cases, the cartridge is held in place by a lock nut or retaining clip. You can use a specialized tool to remove the retaining nut or clip and position the tool on the flat sides of the cartridge. If you cannot locate the retaining clip, you can use a pipe wrench or adjustable pliers.

To remove a cartridge from a faucet, you can use a plastic tool with notches on its side. You can then use pliers to hold the stem and lift it straight up. While you’re trying to remove the cartridge, some water will spill out. If you have trouble removing the cartridge, you can use a special tool known as a cartridge puller. It will help you remove stuck cartridges without damaging your faucet.

A replacement cartridge is fairly simple. To insert a new cartridge, first, remove the old one. You should then align the tabs on the new cartridge with the notches on the faucet body. To make the process easier, you can apply the plumber’s grease to the cartridge’s O-rings. Then, insert the new cartridge into the faucet body. It is important to align the tabs properly so the cartridge will fit properly.

Replacing A Ceramic Disc Valve

A ceramic-disk faucet can have water leaks or flow problems. To repair one, you must replace the cartridge and seals. To do this, disassemble the faucet and drain the water supply. Use a nonmetallic scrubber to clean the openings of the ceramic disk valve. Install new seals. If you can’t get the cartridge out, you can use silicone grease to coat the new O-rings.

To replace the cartridge, disassemble the faucet. The seals and water ports should be cleaned and lubricated with a solution made for plumbing applications. Often, a faulty seal will cause the faucet to leak. To fix the leak, follow the same steps as for a new faucet. Clean the faucet with an old toothbrush to remove sediment and other debris. Once the ceramic disc cartridge is removed, unscrew the trim cap. Use a rubber glove to grip the trim cap. Pull the stem of the ceramic disc cartridge from the faucet body.

Another benefit to replacing ceramic disc valves in faucets is their longevity. They are remarkably durable and can withstand varying temperatures. The replacement ceramic discs are easy to find and are typically more expensive than their rubber counterparts. However, these valves tend to last longer than their rubber washer counterparts and require less maintenance than their rubber counterparts. If you want to replace a ceramic disc valve in a faucet, Moody Plumbing Inc. is here to help you.

Replacing an O-ring

During routine maintenance, replacing the O-ring in your faucet will save you money. These little components often wear out over time. If you notice that your faucet is leaking or producing pulses of high water pressure, replace the O-ring to stop the leak. Replace the entire faucet if this doesn’t work, or you can replace only the O-ring. Replacing the O-ring is a relatively simple process that doesn’t require any special tools or knowledge.

To replace the O-ring on your faucet, remove the stem from the valve body. Then, use a flat-head screwdriver to remove the old O-ring from the valve. Then, apply the plumber’s grease to the replacement O-ring. If the leak has already occurred in the cartridge, replace the stem. To repair the single-handle faucet, you must remove the retaining nut, and twist the spout up and out of the faucet body. Finally, replace the new stem and cartridge.

If you are having trouble with the O-ring, you can replace it yourself. Many faucets come with a cartridge containing ceramic discs. This type of O-ring rarely needs repair. Many manufacturers offer lifetime guarantees on their cartridges. By replacing the seals, you can save money and time. You’ll also avoid wasting water by calling a plumber. You can also take your faucet apart to find the leak.

Replacing A Packing Nut

Replacing a packing nut is the most common repair project for faucets. These little nuts are located at the base of the faucet, under the handle. To replace them, you must first loosen them. Alternatively, you can use a spanner wrench to tighten them. Ensure the nut has enough tension against the stainless steel ball. Follow the steps below to replace a packing nut on a faucet.

A leaky faucet can be caused by a loose or bad packing nut. The leak is most likely to be along the handle. To tighten the packing nut, you must first unscrew the handle. Next, remove the escutcheon cap. If this is not possible, you can use a wrench or pliers to remove the handle and the packing nut. If the packing nut is already loose, you need to replace it.

Depending on the type of faucet, you will need to remove the handle and decorative cap. Then, use your screwdriver to pry the stem upwards. Don’t bang the handle, as you may damage the inner workings. If you can’t remove the stem with your fingers, use a cloth to protect it. Once you’ve removed the handles, you can remove the packing nut. Alternatively, you can use Teflon tape to tighten it gently.

Replacing A Washer

If your faucet is leaking, you can fix it by replacing the washer. A seat washer is the part of a faucet that gets compressed when the handles close. To replace this part, you’ll need a wrench. You’ll also need a screwdriver. Remove the screw and unscrew the seat washer. It’s usually located at the base of the stem. Replace the seat washer with a new one.

Performing a faucet repair by replacing the washer is relatively easy, and requires no plumbing knowledge. Generally, it takes less than an hour to complete. However, if you don’t have a lot of mechanical experience, you may want to call a plumber. The steps for this repair are different depending on the type of faucet. For example, a traditional faucet repair involves replacing the washer and O-ring. Meanwhile, a monobloc lever faucet repair involves replacing the ceramic disk.

The most common cause of a leaking faucet is a faulty washer. The washer is the part that seals against the valve seat. If it’s faulty, it will cause the faucet to leak and leave deposits in your sink. A small chip or other damage will cause the faucet to leak. Replace the washer and the valve stem O-ring. Replacing the parts of a faucet repair can take about ten minutes.